From f5c4671bfbad96bf346bd7e9a21fc4317b4959df Mon Sep 17 00:00:00 2001 From: Indrajith K L Date: Sat, 3 Dec 2022 17:00:20 +0530 Subject: Adds most of the tools --- coreutils-5.3.0-bin/man/cat1p/od.1p.txt | 641 ++++++++++++++++++++++++++++++++ 1 file changed, 641 insertions(+) create mode 100644 coreutils-5.3.0-bin/man/cat1p/od.1p.txt (limited to 'coreutils-5.3.0-bin/man/cat1p/od.1p.txt') diff --git a/coreutils-5.3.0-bin/man/cat1p/od.1p.txt b/coreutils-5.3.0-bin/man/cat1p/od.1p.txt new file mode 100644 index 0000000..c64c3ae --- /dev/null +++ b/coreutils-5.3.0-bin/man/cat1p/od.1p.txt @@ -0,0 +1,641 @@ +od(P) od(P) + + + + + +NAME + od - dump files in various formats + +SYNOPSIS + od [-v][-A address_base][-j skip][-N count][-t + type_string]... + [file...] + + + + od [-bcdosx][file] [[+]offset[.][b]] + + +DESCRIPTION + The od utility shall write the contents of its input + files to standard output in a user-specified format. + +OPTIONS + The od utility shall conform to the Base Definitions + volume of IEEE Std 1003.1-2001, Section 12.2, Utility + Syntax Guidelines, except that the order of presentation + of the -t options and the -bcdosx options is signifi- + cant. + + The following options shall be supported: + + -A address_base + + Specify the input offset base. See the EXTENDED + DESCRIPTION section. The application shall + ensure that the address_base option-argument is a + character. The characters 'd' , 'o' , and 'x' + specify that the offset base shall be written in + decimal, octal, or hexadecimal, respectively. The + character 'n' specifies that the offset shall not + be written. + + -b Interpret bytes in octal. This shall be equiva- + lent to -t o1. + + -c Interpret bytes as characters specified by the + current setting of the LC_CTYPE category. Certain + non-graphic characters appear as C escapes: + "NUL=\0" , "BS=\b" , "FF=\f" , "NL=\n" , "CR=\r" + , "HT=\t" ; others appear as 3-digit octal num- + bers. + + -d Interpret words (two-byte units) in unsigned dec- + imal. This shall be equivalent to -t u2. + + -j skip + Jump over skip bytes from the beginning of the + input. The od utility shall read or seek past the + first skip bytes in the concatenated input files. + If the combined input is not at least skip bytes + long, the od utility shall write a diagnostic + message to standard error and exit with a non- + zero exit status. + + By default, the skip option-argument shall be inter- + preted as a decimal number. With a leading 0x or 0X, the + offset shall be interpreted as a hexadecimal number; + otherwise, with a leading '0' , the offset shall be + interpreted as an octal number. Appending the character + 'b' , 'k' , or 'm' to offset shall cause it to be inter- + preted as a multiple of 512, 1024, or 1048576 bytes, + respectively. If the skip number is hexadecimal, any + appended 'b' shall be considered to be the final hexa- + decimal digit. + + -N count + Format no more than count bytes of input. By + default, count shall be interpreted as a decimal + number. With a leading 0x or 0X, count shall be + interpreted as a hexadecimal number; otherwise, + with a leading '0' , it shall be interpreted as + an octal number. If count bytes of input (after + successfully skipping, if -j skip is specified) + are not available, it shall not be considered an + error; the od utility shall format the input that + is available. + + -o Interpret words (two-byte units) in octal. This + shall be equivalent to -t o2. + + -s Interpret words (two-byte units) in signed deci- + mal. This shall be equivalent to -t d2. + + -t type_string + + Specify one or more output types. See the + EXTENDED DESCRIPTION section. The application + shall ensure that the type_string option-argument + is a string specifying the types to be used when + writing the input data. The string shall consist + of the type specification characters a , c , d , + f , o , u , and x , specifying named character, + character, signed decimal, floating point, octal, + unsigned decimal, and hexadecimal, respectively. + The type specification characters d , f , o , u , + and x can be followed by an optional unsigned + decimal integer that specifies the number of + bytes to be transformed by each instance of the + output type. The type specification character f + can be followed by an optional F , D , or L indi- + cating that the conversion should be applied to + an item of type float, double, or long double, + respectively. The type specification characters d + , o , u , and x can be followed by an optional C + , S , I , or L indicating that the conversion + should be applied to an item of type char, short, + int, or long, respectively. Multiple types can be + concatenated within the same type_string and mul- + tiple -t options can be specified. Output lines + shall be written for each type specified in the + order in which the type specification characters + are specified. + + -v Write all input data. Without the -v option, any + number of groups of output lines, which would be + identical to the immediately preceding group of + output lines (except for the byte offsets), shall + be replaced with a line containing only an aster- + isk ( '*' ). + + -x Interpret words (two-byte units) in hexadecimal. + This shall be equivalent to -t x2. + + + Multiple types can be specified by using multiple + -bcdostx options. Output lines are written for each + type specified in the order in which the types are spec- + ified. + +OPERANDS + The following operands shall be supported: + + file A pathname of a file to be read. If no file oper- + ands are specified, the standard input shall be + used. + + If there are no more than two operands, none of the -A, + -j, -N, or -t options is specified, and either of the + following is true: the first character of the last oper- + and is a plus sign ( '+' ), or there are two operands + and the first character of the last operand is numeric; + the last operand shall be interpreted as an offset op- + erand on XSI-conformant systems. Under these condi- + tions, the results are unspecified on systems that are + not XSI-conformant systems. + + [+]offset[.][b] + The offset operand specifies the offset in the + file where dumping is to commence. This operand + is normally interpreted as octal bytes. If '.' is + appended, the offset shall be interpreted in dec- + imal. If 'b' is appended, the offset shall be + interpreted in units of 512 bytes. + + +STDIN + The standard input shall be used only if no file oper- + ands are specified. See the INPUT FILES section. + +INPUT FILES + The input files can be any file type. + +ENVIRONMENT VARIABLES + The following environment variables shall affect the + execution of od: + + LANG Provide a default value for the internationaliza- + tion variables that are unset or null. (See the + Base Definitions volume of IEEE Std 1003.1-2001, + Section 8.2, Internationalization Variables for + the precedence of internationalization variables + used to determine the values of locale cate- + gories.) + + LC_ALL If set to a non-empty string value, override the + values of all the other internationalization + variables. + + LC_CTYPE + Determine the locale for the interpretation of + sequences of bytes of text data as characters + (for example, single-byte as opposed to multi- + byte characters in arguments and input files). + + LC_MESSAGES + Determine the locale that should be used to + affect the format and contents of diagnostic mes- + sages written to standard error. + + LC_NUMERIC + + Determine the locale for selecting the radix + character used when writing floating-point for- + matted output. + + NLSPATH + Determine the location of message catalogs for + the processing of LC_MESSAGES . + + +ASYNCHRONOUS EVENTS + Default. + +STDOUT + See the EXTENDED DESCRIPTION section. + +STDERR + The standard error shall be used only for diagnostic + messages. + +OUTPUT FILES + None. + +EXTENDED DESCRIPTION + The od utility shall copy sequentially each input file + to standard output, transforming the input data accord- + ing to the output types specified by the -t option or + the -bcdosx options. If no output type is specified, + the default output shall be as if -t oS had been speci- + fied. + + The number of bytes transformed by the output type spec- + ifier c may be variable depending on the LC_CTYPE cate- + gory. + + The default number of bytes transformed by output type + specifiers d , f , o , u , and x corresponds to the var- + ious C-language types as follows. If the c99 compiler is + present on the system, these specifiers shall correspond + to the sizes used by default in that compiler. Other- + wise, these sizes may vary among systems that conform to + IEEE Std 1003.1-2001. + + For the type specifier characters d , o , u , and + x , the default number of bytes shall correspond + to the size of the underlying implementation's + basic integer type. For these specifier charac- + ters, the implementation shall support values of + the optional number of bytes to be converted cor- + responding to the number of bytes in the C-lan- + guage types char, short, int, and long. These + numbers can also be specified by an application + as the characters 'C' , 'S' , 'I' , and 'L' , + respectively. The implementation shall also sup- + port the values 1, 2, 4, and 8, even if it pro- + vides no C-Language types of those sizes. The + implementation shall support the decimal value + corresponding to the C-language type long long. + The byte order used when interpreting numeric + values is implementation-defined, but shall cor- + respond to the order in which a constant of the + corresponding type is stored in memory on the + system. + + For the type specifier character f , the default + number of bytes shall correspond to the number of + bytes in the underlying implementation's basic + double precision floating-point data type. The + implementation shall support values of the + optional number of bytes to be converted corre- + sponding to the number of bytes in the C-language + types float, double, and long double. These num- + bers can also be specified by an application as + the characters 'F' , 'D' , and 'L' , respec- + tively. + + The type specifier character a specifies that bytes + shall be interpreted as named characters from the Inter- + national Reference Version (IRV) of the ISO/IEC 646:1991 + standard. Only the least significant seven bits of each + byte shall be used for this type specification. Bytes + with the values listed in the following table shall be + written using the corresponding names for those charac- + ters. + Table: Named Characters in od +Value Name Value Name Value Name Value Name +\000 nul \001 soh \002 stx \003 etx +\004 eot \005 enq \006 ack \007 bel +\010 bs \011 ht \012 lf or nl \013 vt +\014 ff \015 cr \016 so \017 si +\020 dle \021 dc1 \022 dc2 \023 dc3 +\024 dc4 \025 nak \026 syn \027 etb +\030 can \031 em \032 sub \033 esc +\034 fs \035 gs \036 rs \037 us +\040 sp \177 del + + Note: The "\012" value may be written either as lf or + nl. + + + The type specifier character c specifies that bytes + shall be interpreted as characters specified by the cur- + rent setting of the LC_CTYPE locale category. Characters + listed in the table in the Base Definitions volume of + IEEE Std 1003.1-2001, Chapter 5, File Format Notation ( + '\\' , '\a' , '\b' , '\f' , '\n' , '\r' , '\t' , '\v' ) + shall be written as the corresponding escape sequences, + except that backslash shall be written as a single back- + slash and a NUL shall be written as '\0' . Other non- + printable characters shall be written as one three-digit + octal number for each byte in the character. If the size + of a byte on the system is greater than nine bits, the + format used for non-printable characters is implementa- + tion-defined. Printable multi-byte characters shall be + written in the area corresponding to the first byte of + the character; the two-character sequence "**" shall be + written in the area corresponding to each remaining byte + in the character, as an indication that the character is + continued. When either the -j skip or -N count option is + specified along with the c type specifier, and this + results in an attempt to start or finish in the middle + of a multi-byte character, the result is implementation- + defined. + + The input data shall be manipulated in blocks, where a + block is defined as a multiple of the least common mul- + tiple of the number of bytes transformed by the speci- + fied output types. If the least common multiple is + greater than 16, the results are unspecified. Each + input block shall be written as transformed by each out- + put type, one per written line, in the order that the + output types were specified. If the input block size is + larger than the number of bytes transformed by the out- + put type, the output type shall sequentially transform + the parts of the input block, and the output from each + of the transformations shall be separated by one or more + s. + + If, as a result of the specification of the -N option or + end-of-file being reached on the last input file, input + data only partially satisfies an output type, the input + shall be extended sufficiently with null bytes to write + the last byte of the input. + + Unless -A n is specified, the first output line produced + for each input block shall be preceded by the input off- + set, cumulative across input files, of the next byte to + be written. The format of the input offset is unspeci- + fied; however, it shall not contain any s, shall + start at the first character of the output line, and + shall be followed by one or more s. In addition, + the offset of the byte following the last byte written + shall be written after all the input data has been pro- + cessed, but shall not be followed by any s. + + If no -A option is specified, the input offset base is + unspecified. + +EXIT STATUS + The following exit values shall be returned: + + 0 All input files were processed successfully. + + >0 An error occurred. + + +CONSEQUENCES OF ERRORS + Default. + + The following sections are informative. + +APPLICATION USAGE + XSI-conformant applications are warned not to use file- + names starting with '+' or a first operand starting with + a numeric character so that the old functionality can be + maintained by implementations, unless they specify one + of the -A, -j, or -N options. To guarantee that one of + these filenames is always interpreted as a filename, an + application could always specify the address base format + with the -A option. + +EXAMPLES + If a file containing 128 bytes with decimal values zero + to 127, in increasing order, is supplied as standard + input to the command: + + + od -A d -t a + + on an implementation using an input block size of 16 + bytes, the standard output, independent of the current + locale setting, would be similar to: + + + 0000000 nul soh stx etx eot enq ack bel bs ht nl vt ff cr so si + 0000016 dle dc1 dc2 dc3 dc4 nak syn etb can em sub esc fs gs rs us + 0000032 sp ! " # $ % & ' ( ) * + , - . / + 0000048 0 1 2 3 4 5 6 7 8 9 : ; < = > ? + 0000064 @ A B C D E F G H I J K L M N O + 0000080 P Q R S T U V W X Y Z [ \ ] ^ _ + 0000096 ` a b c d e f g h i j k l m n o + 0000112 p q r s t u v w x y z { | } ~ del + 0000128 + + Note that this volume of IEEE Std 1003.1-2001 allows nl + or lf to be used as the name for the ISO/IEC 646:1991 + standard IRV character with decimal value 10. The IRV + names this character lf (line feed), but traditional + implementations have referred to this character as new- + line ( nl) and the POSIX locale character set symbolic + name for the corresponding character is a . + + The command: + + + od -A o -t o2x2x -N 18 + + on a system with 32-bit words and an implementation + using an input block size of 16 bytes could write 18 + bytes in approximately the following format: + + + 0000000 032056 031440 041123 042040 052516 044530 020043 031464 + 342e 3320 4253 4420 554e 4958 2023 3334 + 342e3320 42534420 554e4958 20233334 + 0000020 032472 + 353a + 353a0000 + 0000022 + + The command: + + + od -A d -t f -t o4 -t x4 -N 24 -j 0x15 + + on a system with 64-bit doubles (for example, + IEEE Std 754-1985 double precision floating-point for- + mat) would skip 21 bytes of input data and then write 24 + bytes in approximately the following format: + + + 0000000 1.00000000000000e+00 1.57350000000000e+01 + 07774000000 00000000000 10013674121 35341217270 + 3ff00000 00000000 402f3851 eb851eb8 + 0000016 1.40668230000000e+02 + 10030312542 04370303230 + 40619562 23e18698 + 0000024 + +RATIONALE + The od utility went through several names in early pro- + posals, including hd, xd, and most recently hexdump. + There were several objections to all of these based on + the following reasons: + + The hd and xd names conflicted with historical + utilities that behaved differently. + + The hexdump description was much more complex + than needed for a simple dump utility. + + The od utility has been available on all histori- + cal implementations and there was no need to cre- + ate a new name for a utility so similar to the + historical od utility. + + The original reasons for not standardizing historical od + were also fairly widespread. Those reasons are given + below along with rationale explaining why the standard + developers believe that this version does not suffer + from the indicated problem: + + The BSD and System V versions of od have + diverged, and the intersection of features pro- + vided by both does not meet the needs of the user + community. In fact, the System V version only + provides a mechanism for dumping octal bytes and + shorts, signed and unsigned decimal shorts, hexa- + decimal shorts, and ASCII characters. BSD added + the ability to dump floats, doubles, named ASCII + characters, and octal, signed decimal, unsigned + decimal, and hexadecimal longs. The version pre- + sented here provides more normalized forms for + dumping bytes, shorts, ints, and longs in octal, + signed decimal, unsigned decimal, and hexadeci- + mal; float, double, and long double; and named + ASCII as well as current locale characters. + + It would not be possible to come up with a + compatible superset of the BSD and System V flags + that met the requirements of the standard devel- + opers. The historical default od output is the + specified default output of this utility. None of + the option letters chosen for this version of od + conflict with any of the options to historical + versions of od. + + On systems with different sizes for short, int, + and long, there was no way to ask for dumps of + ints, even in the BSD version. Because of the way + options are named, the name space could not be + extended to solve these problems. This is why the + -t option was added (with type specifiers more + closely matched to the printf() formats used in + the rest of this volume of IEEE Std 1003.1-2001) + and the optional field sizes were added to the d + , f , o , u , and x type specifiers. It is also + one of the reasons why the historical practice + was not mandated as a required obsolescent form + of od. (Although the old versions of od are not + listed as an obsolescent form, implementations + are urged to continue to recognize the older + forms for several more years.) The a , c , f , o + , and x types match the meaning of the corre- + sponding format characters in the historical + implementations of od except for the default + sizes of the fields converted. The d format is + signed in this volume of IEEE Std 1003.1-2001 to + match the printf() notation. (Historical versions + of od used d as a synonym for u in this version. + The System V implementation uses s for signed + decimal; BSD uses i for signed decimal and s for + null-terminated strings.) Other than d and u , + all of the type specifiers match format charac- + ters in the historical BSD version of od. + + The sizes of the C-language types char, short, + int, long, float, double, and long double are + used even though it is recognized that there may + be zero or more than one compiler for the C lan- + guage on an implementation and that they may use + different sizes for some of these types. (For + example, one compiler might use 2 bytes shorts, 2 + bytes ints, and 4 bytes longs, while another com- + piler (or an option to the same compiler) uses 2 + bytes shorts, 4 bytes ints, and 4 bytes longs.) + Nonetheless, there has to be a basic size known + by the implementation for these types, corre- + sponding to the values reported by invocations of + the getconf utility when called with system_var + operands {UCHAR_MAX}, {USHORT_MAX}, {UINT_MAX}, + and {ULONG_MAX} for the types char, short, int, + and long, respectively. There are similar con- + stants required by the ISO C standard, but not + required by the System Interfaces volume of + IEEE Std 1003.1-2001 or this volume of + IEEE Std 1003.1-2001. They are {FLT_MANT_DIG}, + {DBL_MANT_DIG}, and {LDBL_MANT_DIG} for the types + float, double, and long double, respectively. If + the optional c99 utility is provided by the + implementation and used as specified by this vol- + ume of IEEE Std 1003.1-2001, these are the sizes + that would be provided. If an option is used that + specifies different sizes for these types, there + is no guarantee that the od utility is able to + interpret binary data output by such a program + correctly. + + This volume of IEEE Std 1003.1-2001 requires that + the numeric values of these lengths be recognized + by the od utility and that symbolic forms also be + recognized. Thus, a conforming application can + always look at an array of unsigned long data + elements using od -t uL. + + The method of specifying the format for the + address field based on specifying a starting off- + set in a file unnecessarily tied the two + together. The -A option now specifies the address + base and the -S option specifies a starting off- + set. + + It would be difficult to break the dependence on + U.S. ASCII to achieve an internationalized util- + ity. It does not seem to be any harder for od to + dump characters in the current locale than it is + for the ed or sed l commands. The c type speci- + fier does this without difficulty and is com- + pletely compatible with the historical implemen- + tations of the c format character when the cur- + rent locale uses a superset of the + ISO/IEC 646:1991 standard as a codeset. The a + type specifier (from the BSD a format character) + was left as a portable means to dump ASCII (or + more correctly ISO/IEC 646:1991 standard (IRV)) + so that headers produced by pax could be deci- + phered even on systems that do not use the + ISO/IEC 646:1991 standard as a subset of their + base codeset. + + The use of "**" as an indication of continuation of a + multi-byte character in c specifier output was chosen + based on seeing an implementation that uses this method. + The continuation bytes have to be marked in a way that + is not ambiguous with another single-byte or multi-byte + character. + + An early proposal used -S and -n, respectively, for the + -j and -N options eventually selected. These were + changed to avoid conflicts with historical implementa- + tions. + + The original standard specified -t o2 as the default + when no output type was given. This was changed to -t oS + (the length of a short) to accommodate a supercomputer + implementation that historically used 64 bits as its + default (and that defined shorts as 64 bits). This + change should not affect conforming applications. The + requirement to support lengths of 1, 2, and 4 was added + at the same time to address an historical implementation + that had no two-byte data types in its C compiler. + + The use of a basic integer data type is intended to + allow the implementation to choose a word size commonly + used by applications on that architecture. + +FUTURE DIRECTIONS + All option and operand interfaces marked as extensions + may be withdrawn in a future version. + +SEE ALSO + c99 , sed + +COPYRIGHT + Portions of this text are reprinted and reproduced in + electronic form from IEEE Std 1003.1, 2003 Edition, + Standard for Information Technology -- Portable Operat- + ing System Interface (POSIX), The Open Group Base Speci- + fications Issue 6, Copyright (C) 2001-2003 by the + Institute of Electrical and Electronics Engineers, Inc + and The Open Group. In the event of any discrepancy + between this version and the original IEEE and The Open + Group Standard, the original IEEE and The Open Group + Standard is the referee document. The original Standard + can be obtained online at http://www.open- + group.org/unix/online.html . + + + +POSIX 2003 od(P) -- cgit v1.2.3